Vintage Car Parts

Orderline: +44 (0)1684 212882

£GBP
  • Prices in currencies other than GBP are for guidance only. The actual rate will be that used by the credit card company at the time of billing.

  • Vat is applicable to all UK orders.
    Vat is also applicable to EU orders unless supported by a Valid EEC Vat number entered in your Account details (or when checking out). THIS WILL BE CHECKED WHEN ORDERS ARE PROCESSED.

Index Keywords
  • A
  • B
  • C
  • D
  • E
  • F
  • G
  • H
  • I
  • J
  • K
  • L
  • M
  • N
  • O
  • P
  • Q
  • R
  • S
  • T
  • U
  • V
  • W
  • X
  • Y
  • Z
  • Show All

Lost wax cast bronze lever for CA456 taps. 64mm total length and 17mm wide at ear. Cross hole recessed and threaded for a pan head M4 screw (supplied) to allow the lever to be tightened on to the hexagonal tap spindle. Hole broached for 7mm across flats hexagon fitting.

Fuel resistant (neoprene) rubberised cork gasket that fits our 973, CA456 and 575 taps, 36mm in diameter, 3mm thick with two 7.5mm locating tags.

Three way tap with 3/8" BSP male threads. Brass body with cork under lever. Supplied without nuts and nipples, please order them separately. Overall dimensions with nuts and nipples fitted - 100mm tall x 45mm wide. Mounting bracket hole centres 53mm apart.  Three position - centre position for off, then left or right to select either feed. Made to an original ENOTS pattern. Base and thumb lever are lost wax cast in bronze and then machined. A well made traditional tap.

ENOTS three way tap with cork plate and 3/8" BSP male threads, for 3/8" OD copper tube fittings, to be ordered separately. The hexagonal bar that the lever is attached to can be modified if required, so the lever can be fixed to the dash board. Base mounting holes on tap body with centres 53mm apart. Overall dimensions 68mm long (including threads) and 40mm wide. Mounting bracket is 68mm wide with 53mm hole centres. Control lever pillar 70mm tall (including lever), lever tongue 50mm long. Three position - Centre for off, then left or right to open either feed. Base, tap head and thump lever are lost wax cast in bronze and then machined. 

ENOTS pattern three way tap with cork plate and 1/4" BSP threads, for 1/4'' or 5/16" OD copper tube fittings, to be ordered separately. The hexagonal bar that the lever is attached to can be modified if required, so the lever can be fixed to the dash board. Base mounting holes on tap body with centres 53mm apart. Overall dimensions 68mm long (including threads) and 40mm wide. Mounting bracket is 68mm wide with 53mm hole centres. Control lever pillar 70mm tall (including lever), lever tongue 50mm long. Three position - Centre for off, then left or right to open either feed. Base, tap head and thump lever are lost wax cast in bronze and then machined. 

Three way tap with 1/4" BSP male threads. Brass body with cork under lever. Supplied without nuts and nipples, please order them separately. Overall dimensions with nuts and nipples fitted - 100mm tall x 45mm wide. Mounting bracket hole centres 53mm apart.  Three position - centre position for off, then left or right to select either feed. Made to an original ENOTS pattern. Base and thumb lever are lost wax cast in bronze and then machined. A well made traditional tap.

1/4" BSP male threaded two way tap for solder nut and nipples. All three threaded ends have a 60 degree cone seat. The tap is supplied bare of any fittings, which are to be ordered separately. Dimensions with nuts and nipples fitted - 78mm wide x 47mm tall 42mm deep. A different in/out configuration can be achieved by reassembly of the taper plug and backing quadrant. No off position.

ENOTS type main/reserve tap. Fits into the bottom of some Autovacs. 3/8" BSP male thread for outlet pipework connection, supplied with nut and nipple for solder fitting to 3/8” OD pipe. 1/2" BSP thread into tank - will need a sealing washer e.g. WFC1/2BSP