Prices in currencies other than GBP are for guidance only. The actual rate will be that used by the credit card company at the time of billing.
Min. Shipping :£0.00
VAT (20%): £0.00
Total: £0.00
Prices in currencies other than GBP are for guidance only. The actual rate will be that used by the credit card company at the time of billing.
Wing mounting racing mirror, chrome plated, 4" (100mm) diameter. An aerodynamically styled bullet/racing mirror. Fully adjustable and vibration free. 110mm long, two bolt base of dimensions 93mm x 27mm, with hole centres approx 51mm apart. Offered with choice of FLAT or CONVEX glass. --
Wing mounting racing mirror, chrome plated, 4" (100mm) diameter. An aerodynamically styled bullet/racing mirror. Fully adjustable and vibration free. 110mm long, two bolt base of dimensions 93mm x 27mm, with hole centres approx 51mm apart. Offered with choice of FLAT or CONVEX glass. --
Factory fitment to GM classics of the 50s from Chevrolet, Pontiac, Oldsmobile, Plymouth, though often seen on UK classics and hotrods. Fully adjustable and supplied complete with screws, moulded rubber gasket and fitting template. Fit to door or wing. Polished stainless mirror back with chrome stem. Not handed. Glass diameter approx. 112mm. Length of base approx. 165mm. Overall height 145mm, base 32mm wide 165mm long. Supplied EACH.
Oval type CONVEX glass mirror suitable for vehicles of the '30's. Stamped Desmo, with the mounting bracket on the long side of the oval. Head size 110mm tall x 82mm wide, overall length 153mm. Complete with concave base mounting bracket 58mm x 14mm, hole centres 43mm approx. Our own manufacture, all brass and bronze British construction, reproduced from an original 'Desmo' pattern. Although these were originally made for right hand mounting on the vehicle, we do offer left hand mounting if specified. --
Oval type CONVEX glass mirror suitable for vehicles of the '30's. Stamped Desmo, with the mounting bracket on the long side of the oval. Head size 110mm tall x 82mm wide, overall length 153mm. Complete with concave base mounting bracket 58mm x 14mm, hole centres 43mm approx. Our own manufacture, all brass and bronze British construction, reproduced from an original 'Desmo' pattern. Although these were originally made for right hand mounting on the vehicle, we do offer left hand mounting if specified. --
Oval type CONVEX glass mirror suitable for vehicles of the '30's. Stamped Desmo, with the mounting bracket on the long side of the oval. Head size 110mm tall x 82mm wide, overall length 153mm. Complete with concave base mounting bracket 58mm x 14mm, hole centres 43mm approx. Our own manufacture, all brass and bronze British construction, reproduced from an original 'Desmo' pattern. Although these were originally made for right hand mounting on the vehicle, we do offer left hand mounting if specified. --
Oval type CONVEX glass mirror suitable for vehicles of the '30's. Stamped Desmo, with the mounting bracket on the long side of the oval. Head size 110mm tall x 82mm wide, overall length 153mm. Complete with concave base mounting bracket 58mm x 14mm, hole centres 43mm approx. Our own manufacture, all brass and bronze British construction, reproduced from an original 'Desmo' pattern. Although these were originally made for right hand mounting on the vehicle, we do offer left hand mounting if specified.
Oval mirror equivalent to the Desmo 263 model. Back of mirror casing embossed Desmo. CONVEX mirror glass. Suitable for vehicles of the '30's. Head size 110mm x 82mm, overall length 175mm. Complete with concave base mounting bracket 58mm x 14mm, hole centres 43mm approx. Our own manufacture, brass/bronze construction, recreated from an original 'Desmo' mirror pattern, polished brass, chromium or nickel plated finish. Although these were originally made for right hand mounting, we do offer left hand mounting if specified in the option box. --
Oval mirror equivalent to the Desmo 263 model. Back of mirror casing embossed Desmo. CONVEX mirror glass. Suitable for vehicles of the '30's. Head size 110mm x 82mm, overall length 175mm. Complete with concave base mounting bracket 58mm x 14mm, hole centres 43mm approx. Our own manufacture, brass/bronze construction, recreated from an original 'Desmo' mirror pattern, polished brass, chromium or nickel plated finish. Although these were originally made for right hand mounting, we do offer left hand mounting if specified in the option box. --
Oval mirror equivalent to the Desmo 263 model. Back of mirror casing embossed Desmo. CONVEX mirror glass. Suitable for vehicles of the '30's. Head size 110mm x 82mm, overall length 175mm. Complete with concave base mounting bracket 58mm x 14mm, hole centres 43mm approx. Our own manufacture, brass/bronze construction, recreated from an original 'Desmo' mirror pattern, polished brass, chromium or nickel plated finish. Although these were originally made for right hand mounting, we do offer left hand mounting if specified in the option box. --
Oval mirror equivalent to the Desmo 263 model. Back of mirror casing embossed Desmo. CONVEX mirror glass. Suitable for vehicles of the '30's. Head size 110mm x 82mm, overall length 175mm. Complete with concave base mounting bracket 58mm x 14mm, hole centres 43mm approx. Our own manufacture, brass/bronze construction, recreated from an original 'Desmo' mirror pattern, polished brass, chromium or nickel plated finish. Although these were originally made for right hand mounting, we do offer left hand mounting if specified in the option box.
Rectangular vintage mirror. Arm mounting vintage style rearview car mirror, stamped TOBY. Size 118mm x 67mm, fitted with a clamp for 3/8" (10mm) arm. All brass construction, available with polished brass, chromium or nickel plated finishes. Options for flat or convex (slight wide angle effect) glass. Please select your preferred configuration from the options below. Handmade in Britain. -- Nickel plated brass with convex glass (slight wide-angel view) and stamped with TOBY logo on the back
Rectangular vintage mirror. Arm mounting vintage style rearview car mirror, stamped TOBY. Size 118mm x 67mm, fitted with a clamp for 3/8" (10mm) arm. All brass construction, available with polished brass, chromium or nickel plated finishes. Options for flat or convex (slight wide angle effect) glass. Please select your preferred configuration from the options below. Handmade in Britain. -- Nickel plated brass with Convex glass (slight wide-angle view) and TOBY stamped on the back
Rectangular vintage mirror. Arm mounting vintage style rearview car mirror, stamped TOBY. Size 118mm x 67mm, fitted with a clamp for 3/8" (10mm) arm. All brass construction, available with polished brass, chromium or nickel plated finishes. Options for flat or convex (slight wide angle effect) glass. Please select your preferred configuration from the options below. Handmade in Britain. -- Polished brass with convex glass (slight wide-angel view) and TOBY stamped on back
A large circular rear view mirror 5 1/2" (140mm) in diameter. A splendid reproduction of a large windscreen pillar mounted, early motoring mirror. Fitted with a convex glass lens the unit can be adjusted for length. Suitable for most medium to large-sized vehicles. Arm 10mm diameter, length approx 250mm. Clamps on to approx. 22mm diameter rod. British-made, all brass construction, with investment cast bracket fittings, spun brass head, riveted rear fixing and attractive all-brass clamp assembly. This period mirror design is available in polished brass or nickel-plated finish with a rivetted TOBY medallion badge on the back. The TOBY brand is applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. --
Oval mirror equivalent to the Desmo 263 model. Back of mirror casing embossed 'Toby Mitchell - Toby - London NW1', the mark Vintage Supplies has applied to its authentic reproductions of selected early pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. CONVEX mirror glass. Particularly suitable for vehicles of the '30s and '40s. Head size 110mm x 82mm, overall length 175mm. Complete with concave base mounting bracket 58mm x 14mm, hole centres 43mm approx. Our own manufacture, brass/bronze construction, recreated from an original 'Desmo' mirror pattern, polished brass, chromium or nickel plated finish. Although these were originally made for right hand mounting, we do offer both left and right hand mounting - Please specify your requirement in the drop down option box. -- Nickel plated brass.
Oval mirror equivalent to the Desmo 263 model. Back of mirror casing embossed 'Toby Mitchell - Toby - London NW1', the mark Vintage Supplies has applied to its authentic reproductions of selected early pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. CONVEX mirror glass. Particularly suitable for vehicles of the '30s and '40s. Head size 110mm x 82mm, overall length 175mm. Complete with concave base mounting bracket 58mm x 14mm, hole centres 43mm approx. Our own manufacture, brass/bronze construction, recreated from an original 'Desmo' mirror pattern, polished brass, chromium or nickel plated finish. Although these were originally made for right hand mounting, we do offer both left and right hand mounting - Please specify your requirement in the drop down option box. -- Polished brass finish
Oval-type CONVEX glass mirror suitable for vehicles of the '30's. Stamped TOBY, with the mounting bracket on the long side of the oval. Head size 110mm tall x 82mm wide, overall length 153mm. Complete with concave base mounting bracket 58mm x 14mm, hole centres 43mm approx. Our own manufacture, all brass and bronze British construction, reproduced from an original 'Desmo' pattern. Although these were originally made for right-hand mounting on the vehicle, we do offer left-hand mounting if specified. -- Polished Brass, tall oval-shaped mirror
Oval mirror for arm mounting, stamped marked Desmo. Similar in design to the Desmo 217 model. Head size 110mm x 82mm, fitted with a clamp for 3/8" (10mm) diameter arm. Available in polished brass or chromium or nickel plated finish. CONVEX glass. Desmo stamped to suit left or right mounting. British made, finished and assembled in our workshops. -- Chrome plated brass
Oval mirror for arm mounting, stamped marked Desmo. Similar in design to the Desmo 217 model. Head size 110mm x 82mm, fitted with a clamp for 3/8" (10mm) diameter arm. Available in polished brass or chromium or nickel plated finish. CONVEX glass. Desmo stamped to suit left or right mounting. British made, finished and assembled in our workshops. -- Nickel plated brass
Pillar mounted spotlamp with rear view mirror made to original Raydyot HS495 patten. Chrome on brass. Pillar mounted on adjustable mounting arm and bracket. Lamp 112mm diameter x 93mm deep, mirror 112mm x 29mm, mounting arm 115mm long with 41mm hole centres (bracket overall 57mm x 13mm). Fitted with high quality ball joint allowing universal adjustment and positive lock by finger control. Diffused type glass with clear central section. Supplied complete with bulb and flex. Similar in style and function to some early Eversure and Marchal searchlight models. Supplied with 12v bulb. For replacements use - B111 (6v) or B26 (12v)
Round mirror, 4 3/4" (120mm) in diameter, stamped 'Desmo' on rear of case. 42mm mounting holes centre to centre. Supplied with convex or flat glass . Fitted with the universally adjustable bracket used on many period mirrors. Cast bracket arm onto mirror allows further fine adjustment with a dome into cup arrangement. The bracket is secured with a domed nut. All brass construction, available in chromium or nickel. The head of this handmade British mirror is very similar to the original Lucas 140 model, with a the twin ball joint arrangement allowing improved adjustment. --
Large round rear view mirror suitable for the smaller Edwardian car. Flat type arm clamps to the windscreen frame, optimum diameter to clamp to approx 25mm. 5" (128mm) diameter head, offered with flat glass only. Available in polished brass or chrome plated finish. --
Large round rear view mirror suitable for the smaller Edwardian car. Flat type arm clamps to the windscreen frame, optimum diameter to clamp to approx 25mm. 5" (128mm) diameter head, offered with flat glass only. Available in polished brass or chrome plated finish.
Circular clip on mirror - diameter 90mm. Available in polished brass or stainless steel finish --
Circular clip on mirror - diameter 90mm. Available in polished brass or stainless steel finish
Oval mirror with jointed arm. Fine reproduction of the very popular Raydyot M39 mirror. Head size 110mm x 82mm, fitted with a Raydyot Made in England badge, supplied with CONVEX glass fitted for ease of overtaking, concave base on two hole fixing bracket, width of hole centres 43mm. Overall width 175mm. All brass head and bracket assembly. Offered in chrome plated finish only.
Single point mounting stud for our oval part number CA1262 Raydyot type and 653 Desmo type mirrors, allowing them to be fitted in place with a SINGLE bolt/screw. This fitting replaces the standard two hole mounting bracket, and is ideal for use in limited spaces or where you don't want two holes. Dimensions 25mm long x 15mm diameter, 14.3mm diameter ball to fit the adjustable mirrror coupling on part number 653/CA1262 mirrors. 6mm hole through the centre to take the fixing type/length of your choice. Availalble in polished brass, nickel or chrome plated finish - please select from the options below. --
Single point mounting stud for our oval part number CA1262 Raydyot type and 653 Desmo type mirrors, allowing them to be fitted in place with a SINGLE bolt/screw. This fitting replaces the standard two hole mounting bracket, and is ideal for use in limited spaces or where you don't want two holes. Dimensions 25mm long x 15mm diameter, 14.3mm diameter ball to fit the adjustable mirrror coupling on part number 653/CA1262 mirrors. 6mm hole through the centre to take the fixing type/length of your choice. Availalble in polished brass, nickel or chrome plated finish - please select from the options below. --
Small veteran or vintage pattern mirror. Flat of convex mirror glass (please select below) with heavy rim and backing. Head 100mm diameter. Back of head fitted with two piece brass boss that is pulled tight on the mirror hard with a brass coned nut. Substantial 7/16" diameter straight brass arm approximately 6 1/2" (165mm) long out from the mounting plate. Adjustable knuckle equivalent to the vintage Lucas type mirror fitting, though the mirror size sits below the original Lucas 140 and 150 mirrors. Cast mounting base plate 68mm x 21mm, with two 6.75mm diameter holes at 41mm hole centres. This item is offered in polished brass finish, or nickel plated finish at additional cost and by special order. All brass construction, handmade in Britain. Fitted with a circular brass (or nickel plated) 'Toby' badge on the rear of the mirror case, as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell’s high quality 'Toby' branded product range.
Brass rectangular CONVEX glass mirror. Case 6 1/4" x 3 1/4" (155mm x 80mm) with central rear mounting clamp. Reproduction of a popular style of period mirror produced by Raydyot and Desmo (the very popular Type 36). All brass construction, available in chromium or nickel plated finish, or polished brass. Polished stainless screws to outside of rim. --
Brass rectangular CONVEX glass mirror. Case 6 1/4" x 3 1/4" (155mm x 80mm) with central rear mounting clamp. Reproduction of a popular style of period mirror produced by Raydyot and Desmo (the very popular Type 36). All brass construction, available in chromium or nickel plated finish, or polished brass. Polished stainless screws to outside of rim. --
Small veteran or vintage pattern mirror of the style manufactured by Toby. Flat or convex mirror glass (please select below) with heavy rim and backing. Head 100mm diameter. The back of the head fitted with two piece brass boss that is pulled tight on the mirror hard with a brass coned nut. Substantial 3/8" diameter cranked brass arm approximately 8 1/2" (215mm) long out from mounting plate. Cast mounting base plate 59mm x 21mm, with two 6.75mm diameter holes at 40mm hole centres. This item is offered in polished brass finish, or nickel plated finish at additional cost and by special order. All brass construction, handmade in Britain. Fitted with a circular brass (or nickel plated) 'Toby' badge on the rear of the mirror case, as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell’s high quality 'Toby' branded product range.
Oval mirror with jointed arm. Fine reproduction of this very popular mirror. Head size 110mm x 82mm, fitted with a CONVEX glass for ease of overtaking, concave base on two hole fixing bracket, width of hole centres 43mm. Overall width 175mm. All brass head and bracket assembly. Offered in polished brass, nickel or chrome plated finish. Very similar in style to the Raydyot M39 model. Please note, unlike our 653 mirror, this mirror is NOT embossed on the back of the mirror head. --
Hand spun brass round mirror head 145mm diameter. A quality reproduction of the Lucas 5 5/8" diameter, 150 model mirror. Supplied with flat or convex glass as originally offered - Type 150L and Type 150 respectively. Fitted with 3/8" (10mm) mounting clamp as standard. Available in chromium or nickel plate finish, or as polished brass. The back of the mirror case is fitted with chrome on brass, 18mm diameter 'Toby' medallion or a stamped TOBY logo on the Polished brass version, as applied to our finest period mirror and lamp recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of select CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell 'Toby' branded high-quality product range. --
Hand spun brass round mirror head 145mm diameter. A quality reproduction of the Lucas 5 5/8" diameter, 150 model mirror. Supplied with flat or convex glass as originally offered - Type 150L and Type 150 respectively. Fitted with 3/8" (10mm) mounting clamp as standard. Available in chromium or nickel plate finish, or as polished brass. The back of the mirror case is fitted with chrome on brass, 18mm diameter 'Toby' medallion or a stamped TOBY logo on the Polished brass version, as applied to our finest period mirror and lamp recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of select CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell 'Toby' branded high-quality product range. --
Exterior rear view mirror equivalent to the original Lucas Type 160 mirror. Also very similar to the Eversure No.31 model. 6" x 3 1/4" (152mm x 82mm). CONVEX glass only providing an excellent field of view. 1/2" (12mm) rod diameter clamp as standard - can be changed if required to 7/16" diameter clamp, please indicate your requirement in 'customer comments' at the checkout. Backing plate held in place with 4 screws into internal bracketry. Original equipment for many '30s vehicles including those from MG and Bentley. Pressed brass, stamped Type No 160, Birmingham, England around the centre back of the case. Hand finished and assembled in our workshops. Offered with chrome or nickel plated finish and with or without a period 'Toby' medallion in the back of the mirror casing, as applied to our finest period mirror and lamp recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of select CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. --
Exterior rear view mirror equivalent to the original Lucas Type 160 mirror. Also very similar to the Eversure No.31 model. 6" x 3 1/4" (152mm x 82mm). CONVEX glass only providing an excellent field of view. 1/2" (12mm) rod diameter clamp as standard - can be changed if required to 7/16" diameter clamp, please indicate your requirement in 'customer comments' at the checkout. Backing plate held in place with 4 screws into internal bracketry. Original equipment for many '30s vehicles including those from MG and Bentley. Pressed brass, stamped Type No 160, Birmingham, England around the centre back of the case. Hand finished and assembled in our workshops. Offered with chrome or nickel plated finish and with or without a period 'Toby' medallion in the back of the mirror casing, as applied to our finest period mirror and lamp recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of select CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. --
Hand spun, British-made round brass mirror head, 120mm diameter. A quality recreation of the Lucas 4 3/4" diameter 140 model mirror. Available with convex glass only, as the orignal. Fitted with 3/8" (10mm) mounting clamp as standard. Available as polished brass or in chromium or nickel-plated finish. The back of the nickel and chrome-0plated mirror cases are fitted with an 18mm diameter chrome on brass 'Toby' medallion, as applied to our finest period mirror and lamp recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of select CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell 'Toby' branded high-quality product range. The polished brass version has the same TOBY logo design stamped and filled with black. -- Nickel plated with TOBY medallion to back
Hand spun, British-made round brass mirror head, 120mm diameter. A quality recreation of the Lucas 4 3/4" diameter 140 model mirror. Available with convex glass only, as the orignal. Fitted with 3/8" (10mm) mounting clamp as standard. Available as polished brass or in chromium or nickel-plated finish. The back of the nickel and chrome-0plated mirror cases are fitted with an 18mm diameter chrome on brass 'Toby' medallion, as applied to our finest period mirror and lamp recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of select CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell 'Toby' branded high-quality product range. The polished brass version has the same TOBY logo design stamped and filled with black. -- Chrome plated with TOBY medallion to back
Polished stainless steel clip-on mirror with circular CONVEX glass, 102mm diameter.
Large round rear view mirror suitable for the smaller Edwardian car. Flat type arm clamps to the windscreen frame, optimum diameter to clamp to approx 25mm. 5" (128mm) diameter head, offered with flat glass only. Available in polished brass or chrome plated finish. --
Heavy veteran or Edwardian pattern mirror of a style traditionally manufactured by Toby. Flat mirror glass with bevel edge and heavy rim and backing. Head dimensions 172mm x 135mm. Substantial arm approx 270mm long with very secure mounting base plate 50mm x 63mm. This item is offered in polished brass or with nickel plated finish at additional cost and by special order. The mirror head is hand made in our workshops, the base components lost wax cast with the whole assembly finished by ourselves. Fitted with riveted circular brass or nickel plated 'Toby' badge on rear of case, as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell’s high quality 'Toby' branded product range.
Small round spun brass mirror. Back of case stamped Desmo. 104mm diameter, flat or convex glass. Fitted with 3/8" (10mm) mounting clamp. Available nickel or chrome plated, or polished brass finish. --
Small round spun brass mirror. Back of case stamped Desmo. 104mm diameter, flat or convex glass. Fitted with 3/8" (10mm) mounting clamp. Available nickel or chrome plated, or polished brass finish. --
Small round spun brass mirror. Back of case stamped Desmo. 104mm diameter, flat or convex glass. Fitted with 3/8" (10mm) mounting clamp. Available nickel or chrome plated, or polished brass finish. --
Small round spun brass mirror. Back of case stamped Desmo. 104mm diameter, flat or convex glass. Fitted with 3/8" (10mm) mounting clamp. Available nickel or chrome plated, or polished brass finish.
Larger round mirror, 5 5/8" (145mm) in diameter, stamped Desmo. Supplied with either convex or flat glass. Fitted with a 1/2" (12.7mm) mounting clamp as standard. Available chromium or nickel plated, or in polished brass finish. Hand spun in brass, this vintage mirror is a quality recreation of the Lucas 150 model - flat glass as Type 150L and convex glass as Type 150. --
Larger round mirror, 5 5/8" (145mm) in diameter, stamped Desmo. Supplied with either convex or flat glass. Fitted with a 1/2" (12.7mm) mounting clamp as standard. Available chromium or nickel plated, or in polished brass finish. Hand spun in brass, this vintage mirror is a quality recreation of the Lucas 150 model - flat glass as Type 150L and convex glass as Type 150. --
Larger round mirror, 5 5/8" (145mm) in diameter, stamped Desmo. Supplied with either convex or flat glass. Fitted with a 1/2" (12.7mm) mounting clamp as standard. Available chromium or nickel plated, or in polished brass finish. Hand spun in brass, this vintage mirror is a quality recreation of the Lucas 150 model - flat glass as Type 150L and convex glass as Type 150. --
Larger round mirror, 5 5/8" (145mm) in diameter, stamped Desmo. Supplied with either convex or flat glass. Fitted with a 1/2" (12.7mm) mounting clamp as standard. Available chromium or nickel plated, or in polished brass finish. Hand spun in brass, this vintage mirror is a quality recreation of the Lucas 150 model - flat glass as Type 150L and convex glass as Type 150.
Round mirror, 4 3/4" (120mm) in diameter, stamped Desmo on rear of case. Supplied with convex glass only as original. Fitted with a 3/8" (10mm) mounting clamp as standard. All brass construction, available chromium or nickel plated, or in polished brass finish. This handmade British mirror is very similar in size and appearance to the Desmo No.52PI and Lucas 140 model mirrors. --
Round mirror, 4 3/4" (120mm) in diameter, stamped Desmo on rear of case. Supplied with convex glass only as original. Fitted with a 3/8" (10mm) mounting clamp as standard. All brass construction, available chromium or nickel plated, or in polished brass finish. This handmade British mirror is very similar in size and appearance to the Desmo No.52PI and Lucas 140 model mirrors. --
Round mirror, 4 3/4" (120mm) in diameter, stamped Desmo on rear of case. Supplied with convex glass only as original. Fitted with a 3/8" (10mm) mounting clamp as standard. All brass construction, available chromium or nickel plated, or in polished brass finish. This handmade British mirror is very similar in size and appearance to the Desmo No.52PI and Lucas 140 model mirrors. --
Round mirror, 4 3/4" (120mm) in diameter, stamped Desmo on rear of case. Supplied with convex glass only as original. Fitted with a 3/8" (10mm) mounting clamp as standard. All brass construction, available chromium or nickel plated, or in polished brass finish. This handmade British mirror is very similar in size and appearance to the Desmo No.52PI and Lucas 140 model mirrors.
Oval mirror for arm mounting, stamped marked Desmo. Similar in design to the Desmo 217 model. Head size 110mm x 82mm, fitted with a clamp for 3/8" (10mm) diameter arm. Available in polished brass or chromium or nickel plated finish. CONVEX glass. Desmo stamped to suit left or right mounting. British made, finished and assembled in our workshops. --
Rectangular, arm mounting mirror, stamped Desmo. Size 118mm x 67mm, fitted with a clamp for 3/8" (10mm) arm. All brass construction, available with polished brass, chromium or nickel plated finish, as well as either flat or convex glass. Please select your preferred configuration from the options below. Handmade in Britain. --
Rectangular, arm mounting mirror, stamped Desmo. Size 118mm x 67mm, fitted with a clamp for 3/8" (10mm) arm. All brass construction, available with polished brass, chromium or nickel plated finish, as well as either flat or convex glass. Please select your preferred configuration from the options below. Handmade in Britain. -- flat glass
Rectangular, arm mounting mirror, stamped Desmo. Size 118mm x 67mm, fitted with a clamp for 3/8" (10mm) arm. All brass construction, available with polished brass, chromium or nickel plated finish, as well as either flat or convex glass. Please select your preferred configuration from the options below. Handmade in Britain. -- convex glass
Rectangular, arm mounting mirror, stamped Desmo. Size 118mm x 67mm, fitted with a clamp for 3/8" (10mm) arm. All brass construction, available with polished brass, chromium or nickel plated finish, as well as either flat or convex glass. Please select your preferred configuration from the options below. Handmade in Britain. -- convex glass
Rectangular, arm mounting mirror, stamped Desmo. Size 118mm x 67mm, fitted with a clamp for 3/8" (10mm) arm. All brass construction, available with polished brass, chromium or nickel plated finish, as well as either flat or convex glass. Please select your preferred configuration from the options below. Handmade in Britain. -- convex glass
Rectangular, arm mounting mirror, stamped Desmo. Size 118mm x 67mm, fitted with a clamp for 3/8" (10mm) arm. All brass construction, available with polished brass, chromium or nickel plated finish, as well as either flat or convex glass. Please select your preferred configuration from the options below. Handmade in Britain. --
Single point mounting stud for our oval part number CA1262 Raydyot type and 653 Desmo type mirrors, allowing them to be fitted in place with a SINGLE bolt/screw. This fitting replaces the standard two hole mounting bracket, and is ideal for use in limited spaces or where you don't want two holes. Dimensions 25mm long x 15mm diameter, 14.3mm diameter ball to fit the adjustable mirrror coupling on part number 653/CA1262 mirrors. 6mm hole through the centre to take the fixing type/length of your choice. Availalble in polished brass, nickel or chrome plated finish - please select from the options below. --
Oval type exterior mirror with flat glass suitable for vehicles of the '30's Long head size -128mm x 81mm and overall length of 196mm. Complete with concave base mounting bracket 58mm x 14mm, hole centres 36mm approx. Note period triangular/diamond shaped mounting arm/rear case pressing detail to the mounting edge of rear of mirror. All brass and bronze British construction, chromium plated finish only.
Oval type convex glass mirror equivalent to the Desmo 263 model. Cast bronze Desmo medallion (finished as the mirror body) riveted to the back of the mirror case. Suitable for vehicles of the '30's. Head size 110mm x 82mm, overall length 175mm. Complete with concave base mounting bracket 58mm x 14mm, hole centres 43mm approx. Our own manufacture, brass and bronze construction, recreated from an original 'Desmo' mirror pattern, polished brass, chromium or nickel plated finish. Although these mirrors were originally made for right hand mounting we do offer left hand if specified. The lost wax cast medallion is marked Desmo across the top, with winged car motif in the centre and Birmingham across the bottom, supplied in polished bronze, chrome or nickel plated finish to match the mirror. --
Oval type convex glass mirror equivalent to the Desmo 263 model. Cast bronze Desmo medallion (finished as the mirror body) riveted to the back of the mirror case. Suitable for vehicles of the '30's. Head size 110mm x 82mm, overall length 175mm. Complete with concave base mounting bracket 58mm x 14mm, hole centres 43mm approx. Our own manufacture, brass and bronze construction, recreated from an original 'Desmo' mirror pattern, polished brass, chromium or nickel plated finish. Although these mirrors were originally made for right hand mounting we do offer left hand if specified. The lost wax cast medallion is marked Desmo across the top, with winged car motif in the centre and Birmingham across the bottom, supplied in polished bronze, chrome or nickel plated finish to match the mirror. --
Oval type convex glass mirror equivalent to the Desmo 263 model. Cast bronze Desmo medallion (finished as the mirror body) riveted to the back of the mirror case. Suitable for vehicles of the '30's. Head size 110mm x 82mm, overall length 175mm. Complete with concave base mounting bracket 58mm x 14mm, hole centres 43mm approx. Our own manufacture, brass and bronze construction, recreated from an original 'Desmo' mirror pattern, polished brass, chromium or nickel plated finish. Although these mirrors were originally made for right hand mounting we do offer left hand if specified. The lost wax cast medallion is marked Desmo across the top, with winged car motif in the centre and Birmingham across the bottom, supplied in polished bronze, chrome or nickel plated finish to match the mirror. --
Oval type convex glass mirror equivalent to the Desmo 263 model. Cast bronze Desmo medallion (finished as the mirror body) riveted to the back of the mirror case. Suitable for vehicles of the '30's. Head size 110mm x 82mm, overall length 175mm. Complete with concave base mounting bracket 58mm x 14mm, hole centres 43mm approx. Our own manufacture, brass and bronze construction, recreated from an original 'Desmo' mirror pattern, polished brass, chromium or nickel plated finish. Although these mirrors were originally made for right hand mounting we do offer left hand if specified. The lost wax cast medallion is marked Desmo across the top, with winged car motif in the centre and Birmingham across the bottom, supplied in polished bronze, chrome or nickel plated finish to match the mirror.
A very lightweight alloy mirror with a black base. This is a reproduction of the "Radyot" "Grand Prix" style model, popular on Cobras and many racing cars. The FLAT mirror glass is approx. 90mm diameter. The mirror body is approximately 4" (102mm diameter) and 78mm front to back. The base is 40mm in diameter with an M6 stud, nut and washer.
Good quality clamp on mirror long straight chrome finish arm and 4" diameter polished stainless steel head. Designed to fit on the front edge of a door. Mounting arm 143mm long. Supplied with mounting pads, allen screws and allen key.
Good quality clamp on mirror long shtraight chrome finish arm and 3" diameter polished stainless steel head. Designed to fit on the front edge of a door. Mounting arm 143mm long. Supplied with mounting pads, allen screws and allen key.
Polished stainless mirror back with chrome stem which is suitable for door or wing mounting. This elegant mirror is not handed and can be used on offside or nearside of the vehicle. 120mm diameter mirror head fitted with FLAT glass. Overall height from base to the top of the mirror head 168mm max. Mounting arm is 100mm high x 126mm long with 103mm hole centres. Supplied with a base mounting gasket.
Exterior rear view mirror equivalent to the original Lucas Type 160 mirror. Also very similar to the Eversure No.31 model. 6" x 3 1/4" (152mm x 82mm). CONVEX glass only providing an excellent field of view. 1/2" (12mm) rod diameter clamp as standard - can be changed if required to 7/16" diameter clamp, please indicate your requirement in 'customer comments' at the checkout. Backing plate held in place with 4 screws into internal bracketry. Original equipment for many '30s vehicles including those from MG and Bentley. Pressed brass, stamped Type No 160, Birmingham, England around the centre back of the case. Hand finished and assembled in our workshops. Offered with chrome or nickel plated finish and with or without a period 'Toby' medallion in the back of the mirror casing, as applied to our finest period mirror and lamp recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of select CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. --
Exterior rear view mirror equivalent to the original Lucas Type 160 mirror. Also very similar to the Eversure No.31 model. 6" x 3 1/4" (152mm x 82mm). CONVEX glass only providing an excellent field of view. 1/2" (12mm) rod diameter clamp as standard - can be changed if required to 7/16" diameter clamp, please indicate your requirement in 'customer comments' at the checkout. Backing plate held in place with 4 screws into internal bracketry. Original equipment for many '30s vehicles including those from MG and Bentley. Pressed brass, stamped Type No 160, Birmingham, England around the centre back of the case. Hand finished and assembled in our workshops. Offered with chrome or nickel plated finish and with or without a period 'Toby' medallion in the back of the mirror casing, as applied to our finest period mirror and lamp recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of select CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. --
Highly polished stainless steel mirror head with simple threaded stud mount. Ball joint in back of mirror. Supplied with lock nut, domed nut and washer. High quality distortion-free FLAT mirror glass. 4 1/8" diameter - 4 1/16" glass diameter inside rim - 2 1/2" total depth inluding nut.
Brass rectangular CONVEX glass mirror. Case 6 1/4" x 3 1/4" (155mm x 80mm) with central rear mounting clamp. Reproduction of a popular style of period mirror produced by Raydyot and Desmo (the very popular Type 36). All brass construction, available in chromium or nickel plated finish, or polished brass. Polished stainless screws to outside of rim. --
Brass rectangular CONVEX glass mirror. Case 6 1/4" x 3 1/4" (155mm x 80mm) with central rear mounting clamp. Reproduction of a popular style of period mirror produced by Raydyot and Desmo (the very popular Type 36). All brass construction, available in chromium or nickel plated finish, or polished brass. Polished stainless screws to outside of rim.
Oval mirror with jointed arm. Fine reproduction of this very popular mirror. Head size 110mm x 82mm, fitted with a CONVEX glass for ease of overtaking, concave base on two hole fixing bracket, width of hole centres 43mm. Overall width 175mm. All brass head and bracket assembly. Offered in polished brass, nickel or chrome plated finish. Very similar in style to the Raydyot M39 model. Please note, unlike our 653 mirror, this mirror is NOT embossed on the back of the mirror head. --
Oval mirror with jointed arm. Fine reproduction of this very popular mirror. Head size 110mm x 82mm, fitted with a CONVEX glass for ease of overtaking, concave base on two hole fixing bracket, width of hole centres 43mm. Overall width 175mm. All brass head and bracket assembly. Offered in polished brass, nickel or chrome plated finish. Very similar in style to the Raydyot M39 model. Please note, unlike our 653 mirror, this mirror is NOT embossed on the back of the mirror head. --
Oval mirror with jointed arm. Fine reproduction of this very popular mirror. Head size 110mm x 82mm, fitted with a CONVEX glass for ease of overtaking, concave base on two hole fixing bracket, width of hole centres 43mm. Overall width 175mm. All brass head and bracket assembly. Offered in polished brass, nickel or chrome plated finish. Very similar in style to the Raydyot M39 model. Please note, unlike our 653 mirror, this mirror is NOT embossed on the back of the mirror head.
Chrome finish, clamp to door frame edge, stainless steel exterior mirror. FLAT glass head 112mm diameter, on an arm approx 135mm long. Adjustment to mirror head angle is achieved by slackening a screw in the arm. The base measures approx. 36mm high x 19mm wide and will grip on to max. thickness of 5mm. Please note that the grub screw base is itself held on the chrome arm base with another screw.
Quarterlight clamp on stainless steel mirror. FLAT glass 115mm x 70mm with stainless steel back mounted on a curved arm. Arm extends out 55mm from mounting screws and then 65mm up to the centre of the mirror head. Two grub screws nip the assembly to the edge of the opening quarterlight. Universal mirror that will fit on either the left or right hand side of the vehicle.
American style mirror similar to the MIR310 but fitted with the Lucas 406 style mirror head that offers a much higher degree of adjustment than the centre ball stud on MIR310. Supplied complete with screws, moulded rubber gasket and a fitting template. Fit to door or wing. Polished stainless mirror back with chrome stem. Not handed. Glass diameter approx. 107mm, length of base approx. 165mm, overall height 145mm, base 32mm wide and 165mm long.
Swing back mirror with tapered mirror head shape. 113mm x 102mm stainless steel head. Supplied with CONVEX glass only. Offered with a choice of four designs of chrome stem - please make your selection below. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long ArmC - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs. --
Swing back mirror with tapered mirror head shape. 113mm x 102mm stainless steel head. Supplied with CONVEX glass only. Offered with a choice of four designs of chrome stem - please make your selection below. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long ArmC - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs. --
Swing back mirror with tapered mirror head shape. 113mm x 102mm stainless steel head. Supplied with CONVEX glass only. Offered with a choice of four designs of chrome stem - please make your selection below. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long ArmC - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs. --
Swing back mirror with tapered mirror head shape. 113mm x 102mm stainless steel head. Supplied with CONVEX glass only. Offered with a choice of four designs of chrome stem - please make your selection below. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long ArmC - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs. --
Swing back mirror with tapered mirror head shape. 113mm x 102mm stainless steel head. Supplied with CONVEX glass only. Offered with a choice of four designs of chrome stem - please make your selection below. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long ArmC - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs. --
Swing back mirror with tapered mirror head shape. 113mm x 102mm stainless steel head. Supplied with CONVEX glass only. Offered with a choice of four designs of chrome stem - please make your selection below. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long ArmC - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs.
'Oval' mirror head shape, 126mm x 85mm. Stainless steel head supplied with CONVEX glass only. Offered with a choice of four designs of chrome stem - please make your selection below. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long Arm C - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs. --
'Oval' mirror head shape, 126mm x 85mm. Stainless steel head supplied with CONVEX glass only. Offered with a choice of four designs of chrome stem - please make your selection below. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long Arm C - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs. --
'Oval' mirror head shape, 126mm x 85mm. Stainless steel head supplied with CONVEX glass only. Offered with a choice of four designs of chrome stem - please make your selection below. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long Arm C - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs. --
'Oval' mirror head shape, 126mm x 85mm. Stainless steel head supplied with CONVEX glass only. Offered with a choice of four designs of chrome stem - please make your selection below. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long Arm C - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs. --
'Oval' mirror head shape, 126mm x 85mm. Stainless steel head supplied with CONVEX glass only. Offered with a choice of four designs of chrome stem - please make your selection below. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long Arm C - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs.
'Oval' mirror head shape, 126mm x 85mm. Stainless steel head supplied with CONVEX glass only. Offered with a choice of four designs of chrome stem - please make your selection below. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long Arm C - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs. --
Round shape mirror head. 107mm diameter stainless steel mirror head offered with either CONVEX or FLAT glass. Offered with a choice of four designs of chrome stem - please make your selection below, along with flat or convex glass. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long Arm C - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs - the thread is 1/4" UNF. --
Round shape mirror head. 107mm diameter stainless steel mirror head offered with either CONVEX or FLAT glass. Offered with a choice of four designs of chrome stem - please make your selection below, along with flat or convex glass. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long Arm C - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs - the thread is 1/4" UNF. --
Round shape mirror head. 107mm diameter stainless steel mirror head offered with either CONVEX or FLAT glass. Offered with a choice of four designs of chrome stem - please make your selection below, along with flat or convex glass. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long Arm C - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs - the thread is 1/4" UNF. --
Round shape mirror head. 107mm diameter stainless steel mirror head offered with either CONVEX or FLAT glass. Offered with a choice of four designs of chrome stem - please make your selection below, along with flat or convex glass. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long Arm C - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs - the thread is 1/4" UNF. --
Round shape mirror head. 107mm diameter stainless steel mirror head offered with either CONVEX or FLAT glass. Offered with a choice of four designs of chrome stem - please make your selection below, along with flat or convex glass. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long Arm C - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs - the thread is 1/4" UNF. --
Round shape mirror head. 107mm diameter stainless steel mirror head offered with either CONVEX or FLAT glass. Offered with a choice of four designs of chrome stem - please make your selection below, along with flat or convex glass. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long Arm C - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs - the thread is 1/4" UNF. --
Round shape mirror head. 107mm diameter stainless steel mirror head offered with either CONVEX or FLAT glass. Offered with a choice of four designs of chrome stem - please make your selection below, along with flat or convex glass. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long Arm C - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs - the thread is 1/4" UNF. --
Round shape mirror head. 107mm diameter stainless steel mirror head offered with either CONVEX or FLAT glass. Offered with a choice of four designs of chrome stem - please make your selection below, along with flat or convex glass. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long Arm C - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs - the thread is 1/4" UNF. --
Round shape mirror head. 107mm diameter stainless steel mirror head offered with either CONVEX or FLAT glass. Offered with a choice of four designs of chrome stem - please make your selection below, along with flat or convex glass. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long Arm C - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs - the thread is 1/4" UNF. --
Round shape mirror head. 107mm diameter stainless steel mirror head offered with either CONVEX or FLAT glass. Offered with a choice of four designs of chrome stem - please make your selection below, along with flat or convex glass. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long Arm C - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs - the thread is 1/4" UNF. --
Round shape mirror head. 107mm diameter stainless steel mirror head offered with either CONVEX or FLAT glass. Offered with a choice of four designs of chrome stem - please make your selection below, along with flat or convex glass. All four arms mount through a 16mm hole in the panel and protrude 50mm under. Arm A -Straight, 105mm long Arm B - Curved, 110mm long Arm C - Adjustable, 103mm long Arm D - Short, 70mm long Alternatively, we offer the mirror head only - in which case, the backing nut is not supplied as this comes with the arms and differs - the thread is 1/4" UNF.
Wing mounted mirror equivalent to the Lucas 406 model; an early mirror that remained extremely popular for many years. Ball joint mounted 4 3/16" (106mm) diameter stainless steel mirror head, with chromium stem and single M8 mounting stud. We offer this mirror in handed pairs with either CONVEX or FLAT glass, or left or right handed mirros individually with CONVEX glass. Rubber pad supplied for mounting footprint dimensions 42mm x 32mm. Chrome plated finish only. This is possibly the most popular vintage and classic mirror. Very similar in design to the Eversure model No 44, Tudor No.4 and the Desmo No.165. --
Wing mounted mirror equivalent to the Lucas 406 model; an early mirror that remained extremely popular for many years. Ball joint mounted 4 3/16" (106mm) diameter stainless steel mirror head, with chromium stem and single M8 mounting stud. We offer this mirror in handed pairs with either CONVEX or FLAT glass, or left or right handed mirros individually with CONVEX glass. Rubber pad supplied for mounting footprint dimensions 42mm x 32mm. Chrome plated finish only. This is possibly the most popular vintage and classic mirror. Very similar in design to the Eversure model No 44, Tudor No.4 and the Desmo No.165. -- Please select convex of flat glass using the 'drop down' option box
Wing mounted mirror equivalent to the Lucas 406 model; an early mirror that remained extremely popular for many years. Ball joint mounted 4 3/16" (106mm) diameter stainless steel mirror head, with chromium stem and single M8 mounting stud. We offer this mirror in handed pairs with either CONVEX or FLAT glass, or left or right handed mirros individually with CONVEX glass. Rubber pad supplied for mounting footprint dimensions 42mm x 32mm. Chrome plated finish only. This is possibly the most popular vintage and classic mirror. Very similar in design to the Eversure model No 44, Tudor No.4 and the Desmo No.165. -- Please select convex of flat glass using the 'drop down' option box
Wing mounted mirror equivalent to the Lucas 406 model; an early mirror that remained extremely popular for many years. Ball joint mounted 4 3/16" (106mm) diameter stainless steel mirror head, with chromium stem and single M8 mounting stud. We offer this mirror in handed pairs with either CONVEX or FLAT glass, or left or right handed mirros individually with CONVEX glass. Rubber pad supplied for mounting footprint dimensions 42mm x 32mm. Chrome plated finish only. This is possibly the most popular vintage and classic mirror. Very similar in design to the Eversure model No 44, Tudor No.4 and the Desmo No.165. --
Wing mounted mirror equivalent to the Lucas 406 model; an early mirror that remained extremely popular for many years. Ball joint mounted 4 3/16" (106mm) diameter stainless steel mirror head, with chromium stem and single M8 mounting stud. We offer this mirror in handed pairs with either CONVEX or FLAT glass, or left or right handed mirros individually with CONVEX glass. Rubber pad supplied for mounting footprint dimensions 42mm x 32mm. Chrome plated finish only. This is possibly the most popular vintage and classic mirror. Very similar in design to the Eversure model No 44, Tudor No.4 and the Desmo No.165.
Superb classic chrome mirror that screws to a mounting plate that your attach to your door. Typical of the type used in late 1960's and 1970's. Ideal for many classic cars such as the Mini, MG etc. Mirror head 145mm x 90mm, base footprint approx 85mm x 33mm. FLAT glass. Plinth fixing hole centres 35mm. Offered for left OR right hand door fitting applications. --
Superb classic chrome mirror that screws to a mounting plate that your attach to your door. Typical of the type used in late 1960's and 1970's. Ideal for many classic cars such as the Mini, MG etc. Mirror head 145mm x 90mm, base footprint approx 85mm x 33mm. FLAT glass. Plinth fixing hole centres 35mm. Offered for left OR right hand door fitting applications. --
Superb classic chrome mirror that screws to a mounting plate that your attach to your door. Typical of the type used in late 1960's and 1970's. Ideal for many classic cars such as the Mini, MG etc. Mirror head 145mm x 90mm, base footprint approx 85mm x 33mm. FLAT glass. Plinth fixing hole centres 35mm. Offered for left OR right hand door fitting applications.
Wing mounting racing mirror, chrome plated, 4" (100mm) diameter. An aerodynamically styled bullet/racing mirror. Fully adjustable and vibration free. 110mm long, two bolt base of dimensions 93mm x 27mm, with hole centres approx 51mm apart. Offered with choice of FLAT or CONVEX glass.
Round chrome plated racing mirror. 4" (100mm diameter), 90mm deep, single bolt fixing at base. FLAT glass.
Round lightweight alloy racing mirror. 4" (100mm) diameter, 90mm deep, single bolt fixing at base. FLAT glass.
A classic bullet style exterior mirror appropriate for fitting to wing or door using two mounting holes with centres 50mm apart. FLAT mirror glass approximately 88mm in diameter.
A classic bullet style exterior mirror appropriate for fitting to wing or door using two mounting holes with centres 50mm apart. FLAT mirror glass approximately 88mm in diameter.
Small bullet/racing mirror with single bolt fixing. All black finish. 4" 100mm diameter overall approximately. FLAT glass lens approx. 3 1/2" (90mm) diameter. M6 mounting stud supplied complete with nut and washer. Adjustable mirror head.
Small circular clamp-on mirror. Stainless steel bracket and mirror back. 78mm diameter FLAT glass. Can be fitted without drilling, to either the quarterlight frame, or quarterlight glass pillar gutter. Supplied with all fittings.
Quarterlight glass type clamp on stainless steel mirror. CONVEX glass 115mm x 73mm, with stainless steel mirror back and straight bracket. Two screws nip the assembly to the edge of the opening quarterlight, to suit either the right hand or left hand side.
Large racing mirror with a long matt black base and body. 4" (102mm diameter) and 120mm long overall. Base dimenstion 93mm x 27mm with two fixing holes with centres 50mm apart. Supplied complete with mounting nuts and bolts. FLAT mirror glass approx. 3 1/2" (90mm) diameter.
USA made billet aluminium post mirrors. This comes with a threaded stud that can be screwed in to a pillar or post and the the mirror can be attached to that. Mirror head 81mm total length 170mm. Threaded stud 16mm long, supplied with nyloc nut. Tinted glass.
Gutter mount type clamp on stainless steel mirror. CONVEX glass 115mm x 73mm with stainless steel mirror back and cranked mounting bracket. Two screws nip the assembly to the right hand side of the vehicle - to suit the left hand side of the vehicle, the stainless steel bracket will require re-bending slightly.
Round mirror with long, curved mounting arm. 4" circular polished stainless steel mirror head with 140mm long curved chrome arm. Adjustable mounting bracket. For mounting on the left or right hand side of the vehicle.
Rectangular clip on mirror, designed to fit on the front edge of a door. 64mm x 127mm stainless steel mirror head, 152mm long chrome plated zinc alloy die cast arm.
Racing, bullet type mirror with FLAT glass. Designed to clamp onto the front face of the door or window frame. This mirror will also clamp on to some windscreen surrounds. No drilling required. Fully reversible as the mirror rotates on the arm and the clamp rotates on the arm also. Plastic protective shoe in clamp, grub screws provided.
Polished aluminium racing/bullet mirror, 4" (100mm) diameter and approximately 100mm deep. Currently only available with flat glass lens held in adjustable head section, with screw adjustment. Single bolt mounting (M8 x 30mm long) on base of dimensions 57mm x 20mm. Supplied with a rubber base gasket.
Pair of 50's style chromed wing mirrors - single bolt fixing. Supplied with rubber gaskets. Head size 111mm and stands approx 140mm high, base length 59mm.
Heavy veteran or Edwardian pattern mirror of the style manufactured by Toby. Flat mirror glass with heavy rim and backing. Head 144mm diameter. Substantial arm approximately 270mm long with very secure mounting base plate 50mm x 63mm. This item is offered in polished brass finish, or nickel plated finish at additional cost and by special order. All brass construction, handmade in Britain. Fitted with a riveted circular brass or nickel plated 'Toby' badge on the rear of the mirror case, as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell’s high quality 'Toby' branded product range.
Clamp on circular mirror which will fit to either the left or right side of the vehicle. The head is approx. 3" (78mm) in diameter. Stainless steel mirror back with FLAT glass, mounted on curved chrome plated arm (approx 65mm long) that clamps to the door edge etc. A useful 'peep' mirror. To adjust the mirror for fitting to the opposite side of the vehicle, the clamp bracket can be turned round. For a 4" version, please see part number MIR016.
4" diameter circular 'Peep' mirror. Clips on to door or quarterlight frame with an adjustable bracket. Good quality, stainless steel mirror head and chrome arm. A well made part to improve your car and help address the 'blind spot' problem. This is 4" version of part number CA1377.
Quarterlight glass type clamp on stainless steel mirror. FLAT glass 118mm x 55mm, with stainless steel mirror back and straight bracket. Two screws nip the assembly to the edge of the opening quarterlight, maximum thickness 6mm. To suit either the right hand or left hand side of the vehicle. Supplied with mounting pads, allen screws and allen key.
Large circular clamp on mirror. Stainless steel bracket and mirror back, 4 1/4" (107mm) convex glass. This mirror can be fitted to quarter light frame, or a quarter light glass pillar gutter without drilling. Supplied with all fittings.
ITAL exterior door mirror, polished stainless steel head with CONVEX glass 113mm in diameter. Mounted on a chrome plinth with a single bolt fixing and a locating peg - approximately 29mm between centres. Supplied with a rubber base gasket. Mirror footprint 90mm x 30mm at the widest point. This very popular mirror can also be used as a wing mirror.
New unused original stock part of the Rallye classic outside mirror. Manufactured by Vitaloni of Italy. This mirror is for LEFT side of vehicle mounting only and it will not transpose to mount on other side. Chrome plated classic angular shape body with FLAT glass. Size 124mm x 85mm x 93mm deep. Flat mounting base of dimesions 35mm x 67mm, with two bolt holes with centres 52mm apart. A great classic mirror for LHD vehicles.
Left side fitting stainless steel door mounted bullet mirror. CONVEX glass. Bullet racing mirror with universal fitment, designed for door mounting as on early Minis and many other classic and kit cars. Polished stainless steel head with a chrome plated die cast stem. Dimensions - 102mm diameter, 78mm x 30mm.
Right side fitting stainless steel door mounted bullet mirror. CONVEX glass. Bullet racing mirror with universal fitment, designed for door mounting as on early Minis and many other classic and kit cars. Polished stainless steel head with a chrome plated die cast stem. Dimensions - 102mm diameter, 78mm x 30mm
Superb reproduction of the very popular 'Raydyot' oval mirror with single hole fixing. Chrome on brass finish. Mirror head approx 110 by 82mm. Fitted with our unique single hole fitting stud for improved mounting point flexibility. Flat or convex glass available, please indicate preference. Please note this mirror is NOT embossed on the back of the mirror head.
Wing mounted bullet/racing mirror, polished alloy, 4" (100mm) diameter with CONVEX glass. Aerodynamically styled, fully adjustable and vibration free. 110mm long with two bolt base of dimensions 93mm x 27mm with mounting hole centres approx 51mm apart.
Rounded lightweight alloy racing mirror with rim, 4" (100mm) diameter, single 7mm approx bolt fixing. FLAT glass. The base is riveted and the rim held in place with screws. Self colour. A reproduction of the classic Raydyot design.
A lightweight BLACK coated, alloy racing mirror. A reproduction of the Raydyot "Grand Prix" style model, popular on Cobras and many racing cars. The FLAT mirror glass is approx 3 1/2" (90mm) diameter. The mirror body is approximately 102mm diameter, with the shell approximately 78mm front to back. The base is 40mm diameter and fitted with an M6 stud, nut and washer.
Chromed alloy racing/bullet mirror. A reproduction of the Raydyot "Grand Prix" style model, popular on Cobras and many racing cars. The FLAT mirror glass is approx 3 1/2" (90mm) diameter. The mirror body is approximately 4" (102mm) diameter and 78mm front to back, the base 40mm in diameter and fitted with an M6 stud, nut and washer. For a premium version of this mirror fitted with a chrome 'Raydyot' medallion, please see part number MIR318B.
A lightweight alloy racing mirror. A reproduction of the Raydyot "Grand Prix" style model, popular on Cobras and many racing cars. The FLAT mirror glass is approx 3 1/2" (90mm) diameter. The mirror body is approximately 102mm diameter, with the shell approximately 78mm front to back. The base is 40mm diameter and fitted with an M6 stud, nut and washer. Because of its matt alloy finish, this mirror can be painted to match the body colour of the vehicle without having to use an etching primer.
A pair of 1950's style chromed wing mirrors. Round mirror head on curved arm for mounting on to the wing or door. A single M8 mounting bolt, requiring an 8mm clearance hole in the panel, on shaped base of dimensions 58mm x 18mm. The chrome arm slopes out and toward the rear. Polished stainless mirror head with CONVEX glass approx 112mm diameter. Supplied complete with rubber base gaskets. Offered in PAIRS only.
Exterior rear view mirror equivalent to the original Lucas Type 160 mirror. Also very similar to the Eversure No.31 model. 6" x 3 1/4" (152mm x 82mm). CONVEX glass only providing an excellent field of view. 1/2" (12mm) rod diameter clamp as standard - can be changed if required to 7/16" diameter clamp, please indicate your requirement in 'customer comments' at the checkout. Backing plate held in place with 4 screws into internal bracketry. Original equipment for many '30s vehicles including those from MG and Bentley. Pressed brass, stamped Type No 160, Birmingham, England around the centre back of the case. Hand finished and assembled in our workshops. Offered with chrome or nickel plated finish and with or without a period 'Toby' medallion in the back of the mirror casing, as applied to our finest period mirror and lamp recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of select CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range.
Rectangular, arm mounting mirror, stamped Desmo. Size 118mm x 67mm, fitted with a clamp for 3/8" (10mm) arm. All brass construction, available with polished brass, chromium or nickel plated finish, as well as either flat or convex glass. Please select your preferred configuration from the options below. Handmade in Britain.
Hand spun brass round mirror head 145mm diameter. A quality reproduction of the Lucas 5 5/8" diameter, 150 model mirror. Supplied with flat or convex glass as originally offered - Type 150L and Type 150 respectively. Fitted with 3/8" (10mm) mounting clamp as standard. Available in chromium or nickel plate finish, or as polished brass. The back of the mirror case is fitted with chrome on brass, 18mm diameter 'Toby' medallion or a stamped TOBY logo on the Polished brass version, as applied to our finest period mirror and lamp recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of select CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell 'Toby' branded high-quality product range.
Hand spun, British-made round brass mirror head, 120mm diameter. A quality recreation of the Lucas 4 3/4" diameter 140 model mirror. Available with convex glass only, as the orignal. Fitted with 3/8" (10mm) mounting clamp as standard. Available as polished brass or in chromium or nickel-plated finish. The back of the nickel and chrome-0plated mirror cases are fitted with an 18mm diameter chrome on brass 'Toby' medallion, as applied to our finest period mirror and lamp recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of select CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell 'Toby' branded high-quality product range. The polished brass version has the same TOBY logo design stamped and filled with black.
A large circular rear view mirror 5 1/2" (140mm) in diameter. A splendid reproduction of a large windscreen pillar mounted, early motoring mirror. Fitted with a convex glass lens the unit can be adjusted for length. Suitable for most medium to large-sized vehicles. Arm 10mm diameter, length approx 250mm. Clamps on to approx. 22mm diameter rod. British-made, all brass construction, with investment cast bracket fittings, spun brass head, riveted rear fixing and attractive all-brass clamp assembly. This period mirror design is available in polished brass or nickel-plated finish with a rivetted TOBY medallion badge on the back. The TOBY brand is applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range.
Oval mirror for arm mounting, stamped marked Toby. Similar in design to the Desmo 217 model. Head size 110mm x 82mm, fitted with a clamp for 3/8" (10mm) diameter arm. Available in polished brass or chromium or nickel-plated finish. CONVEX glass. Toby stamped. British-made, finished and assembled in our workshops. -- Nickel plated brass
Circular clip on mirror - diameter 90mm. Available in polished brass or stainless steel finish --
A large circular rear view mirror 5 1/2" (140mm) in diameter. A splendid reproduction of a large windscreen pillar mounted, early motoring mirror. Fitted with a convex glass lens the unit can be adjusted for length. Suitable for most medium to large-sized vehicles. Arm 10mm diameter, length approx 250mm. Clamps on to approx. 22mm diameter rod. British-made, all brass construction, with investment cast bracket fittings, spun brass head, riveted rear fixing and attractive all-brass clamp assembly. This period mirror design is available in polished brass or nickel-plated finish with a rivetted TOBY medallion badge on the back. The TOBY brand is applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. --