Prices in currencies other than GBP are for guidance only. The actual rate will be that used by the credit card company at the time of billing.
Min. Shipping :£0.00
VAT (20%): £0.00
Total: £0.00
Prices in currencies other than GBP are for guidance only. The actual rate will be that used by the credit card company at the time of billing.
PAIR of LED light boards for conversion of Lucas ST51 'D Lamp' type lights fitted with FULL RED lenses to bright LED operation. On board electronics make this product suitable for 6V &12V vehicles, either Positive or Negative earth. This is a new product specially designed to fit the Lucas ST51 lamp and modern reproductions to the original pattern such as Vintage Supplies'/sVc's '249 and 428' part number lamps. The product features a main, D shaped RED light board that locates between the original lens and the lens retaining wire. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination, though the assembly is suitable for D lamps with or without a number plate illumination window. The board is fitted with one BAY15D bulb base connector (15mm diameter, double contact cap with vertically offset pins) on 15cm connecting wires. One contact of the double contact holder illuminates the Tail light (first brightness RED) and the Number Plate light (WHITE). The second contact illuminates the Stop light (second brightness RED). Use of a bulb base style connector allows easy return of the lamp to its original condition if required. These boards have a very low power requirement and provide great all over lens lighting from 36 RED LEDS, with the fast response time/illumination under braking characteristic of LEDs - as well as good distinction between STOP and TAIL brightnesses. This is a 'plug and play' product that requires no other attachment other than plugging in the bulb connector, locating the LED board between the lens and the lens retaining spring clip and reassembly of the lamp. Two 1.5mm thick rubber lens seals are provided in the kit, in case they are needed. Conversion kit for a PAIR of lamps.
A PAIR of LED light boards for conversion of Lucas ST38 'Pork Pie' type lamps fitted with all RED lenses to bright LED operation. On board electronics make this product suitable for 6V & 12V vehicles and Positive & Negative earth systems. This is a new product specially designed to fit the Lucas ST38 lamp and modern reproductions to the original pattern such as '776' part numbered products. Each board features a main, circular RED light panel with a centre slot that fits over/locates on the vertical partition of the triple bulb holder bolted into the ST38 body. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination - though the assembly is suitable for lamps with or without a number plate illumination window. The board is fitted with two BA15S bulb base connectors on 9cm connecting wires. One connection illuminates the Tail light (first brightness RED) and the Number Plate light (WHITE). The other connection illuminates the Stop light (second brightness RED). Use of bulb base style connectors allows easy return of the lamp to its original condition if required. These boards have a very low power requirement and provide great all over lens lighting from 36 RED LEDS, with the fast response time/illumination under braking characteristic of LEDs - plus good distinction between STOP and TAIL brightnesses. This is a 'plug and play' product that requires no attachment other than plugging in the bulb connectors, locating the slot in the LED board over the bulb holder partition and reassembly of the lamp. Two 3mm thick foam lens seals are provided in the kit, incase they are needed for cushioning. Conversion kit for a PAIR of lamps.
PAIR of LED light boards for conversion of Lucas ST51 'D Lamp' type lights, fitted with SPLIT RED lenses, to bright LED operation. On board electronics make this suitable for 6V & 12V vehicles and Positive & Negative earth systems. This is a new product specially designed to fit the Lucas ST51 split lens lamp and modern reproductions to the original pattern such as Vintage Supllies'/sVc's '249A and 428A' part number products. The panel features a main, D shaped RED light board with two sections of LEDs, that locates between the original lens and the lens retaining wire. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination, though the assembly is suitable for D lamps with or without a number plate illumination window. Two versions of this board are available to deal with different designs of 'D lamp': Two BA15S bulb holder connectors (15mm diameter, single contact cap with equal pins) on 15cm connecting wires. One connector illuminates the Tail light (first brightness RED on both section of LEDs) plus the Number Plate light (WHITE). The second connector illuminates the Stop light (second brightness RED on both sections of LED) One BA15S single contact holder and one BA15D double contact equal pin holder - The BA15S connector illuminates the Tail light (first brightness RED on both sections of LEDs) plus the Number Plate light (WHITE). Either terminal on the BA15D connector illuminates the Stop light (second brightness RED on both sections of LED) Please check the bulb holders in your ST51 D Lamp and see whether it has two single contact bulb holders or one single and one double (BA15D) holder - then select either the BA15S/BA15S or BA15S/BA15D panel These boards have a very low power requirement and provide great all over lens lighting from 51 RED LEDS, with the fast response time/illumination under braking characteristic of LEDs - plus good distinction between STOP and TAIL red light brightnesses. This is a 'plug and play' product that requires no other attachment other than plugging in the bulb connectors and locating the LED board between the lens and the lens retaining spring clip and reassembly of the lamp. Two 1.5mm thick rubber lens seals are provided in the kit, in case they are needed. Conversion kit for a PAIR of lamps.
PAIR of all in one LED light boards and split Red/Amber lenses for conversion of Lucas ST51 SPLIT lens 'D Lamp' type Stop & Tail lamps (with or without number plate illumination) fitted with all RED lenses, to Stop, Tail, INDICATOR & number plate illumination operation. On board electronics make this product suitable for 12V vehicles only, either Positive or Negative earth. This is a new product specially designed to fit the Lucas ST51 lamp and modern reproductions to the original pattern, such as Vinate Supplies'/sVc's '249A' and '428A' part numbered products. The product features a main, D shaped light board with two sections of LEDs - one RED and one AMBER - that locates between the original lens and the lens retaining wire. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination, though the assembly is suitable for D lamps with or without a number plate illumination window. The board is fitted with one bulb base BA15D connector (please note - equal NOT offset pin) on 15cm connecting wires and one BA15S bulb base connector on 10cm connecting wires. One terminal of the BA15D base illuminates the Tail light (first brightness RED) and the Number Plate light (WHITE). The second terminal illuminates the Stop light (second brightness RED). The BA15S connection iluminates the AMBER indication/turn signal LEDs. Use of bulb base style connectors allows easy return of the lamp to its original condition if required. These boards have a very low power requirement and provide great all over lens lighting from 27 RED LEDs and 24 AMBER LEDs, with the fast response time/illumination under braking characteristic of LEDs - plus good distinction between STOP and TAIL brightnesses. This is a 'plug and play' product that requires no attachment other than plugging in the two bulb connectors and locating the LED board between the lens and the lens retaining spring clip, then reassembly of the lamps with the new Red/Amber lenses instead of the all Red split lens. Two 1.5mm thick rubber lens seals are provided in the kit, one for each lens if required. Conversion kit for a PAIR of lamps.
A PAIR of all in one LED light boards and split Red/Amber lenses for conversion of Lucas ST38 'Pork Pie' type Stop & Tail lamps (with or without number plate illumination) with all RED lenses to Stop, Tail, INDICATOR & Number Plate illumination operation. On board electronics make this product suitable for 6V & 12V vehicles, and Positive & Negative earth systems. This is a new product specially designed to fit the Lucas ST38 lamp and modern reproductions to the original pattern, such as '776' part numbered products. The product features a main, circular RED and AMBER light board with a centre slot that fits over/locates on the vertical partition of the triple bulb holder bolted into the ST38 body. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination - though the assembly can be used in lamps with or without a number plate illumination window. The board is fitted with three BA15S bulb base connectors on 10cm connecting wires. One connection illuminates the Tail light (first brightness RED) and the Number Plate light (WHITE). The second connection illuminates the Stop light (second brightness RED). The third connection illuminates the AMBER indication/turn signal LEDs. Use of bulb base style connectors allows easy return of the lamp to its original condition if required. These boards have a very low power requirement and provide great all over lens lighting from 30 RED LEDs and 24 AMBER LEDs, with the fast response time/illumination under braking characteristic of LEDs - plus good distinction between STOP and TAIL brightnesses. This is a 'plug and play' product that requires no other attachment other than plugging in the three bulb connectors, locating the slot in the LED board over the original bulb holder partition and reassembly of the lamps with the new Red/Amber lenses instead of the all Red lenses. Four 3mm thick foam lens seals are provided in the kit, one for either side of each lens if required. Conversion kit for a PAIR of lamps.
PAIR of all in one LED light boards to upgrade CA1249 lamps - Lucas type ST38 'Pork Pie' Stop & Tail lamps converted to include indicator functionality with split WEDGE T10 bulb holders and split RED/AMBER lenses. On board electronics make this product suitable for 6V & 12V vehicles and Positive & Negative earth systems. This is a new product specially designed to fit Lucas ST38 lamps (and modern reproductions to the original pattern) that have already been converted to include indicator functionality - Vintage Supplies' or sVc's 'CA1249' part numbered product range. The product features a main, circular RED and AMBER light board with a centre slot that fits over/locates on the vertical partition of the triple WEDGE T10 bulb holder retro bolted into the ST38 lamp body. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination. The board is fitted with three WEDGE T10 bulb base connectors on 10cm connecting wires. One connection illuminates the Tail light (first brightness RED) and the Number Plate light (WHITE). The second connection illuminates the Stop light (second brightness RED). The third connection iluminates the AMBER indication/turn signal LEDs. Use of T10 bulb base style connectors allows easy return of the lamp to its original condition and capless bulb operation if required. These boards have a very low power requirement and provide great all over lens lighting from 30 RED LEDs and 24 AMBER LEDs, with the fast response time/illumination under braking characteristic of LEDs - plus good distinction between STOP and TAIL red light brightnesses. This is a 'plug and play' product that requires no attachment other than plugging in the three T10 bulb connectors, locating the slot in the LED board over the partition and reassembly of the lamp. Two 3mm thick foam lens seals are provided in the kit, incase they are needed for cushioning. Conversion kit for a PAIR of lamps.
PAIR of LED light boards for conversion of Lucas ST51 'D Lamp' type lights, fitted with SPLIT RED lenses, to bright LED operation. On board electronics make this suitable for 6V & 12V vehicles and Positive & Negative earth systems. This is a new product specially designed to fit the Lucas ST51 split lens lamp and modern reproductions to the original pattern such as Vintage Supllies'/sVc's '249A and 428A' part number products. The panel features a main, D shaped RED light board with two sections of LEDs, that locates between the original lens and the lens retaining wire. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination, though the assembly is suitable for D lamps with or without a number plate illumination window. Two versions of this board are available to deal with different designs of 'D lamp': Two BA15S bulb holder connectors (15mm diameter, single contact cap with equal pins) on 15cm connecting wires. One connector illuminates the Tail light (first brightness RED on both section of LEDs) plus the Number Plate light (WHITE). The second connector illuminates the Stop light (second brightness RED on both sections of LED) One BA15S single contact holder and one BA15D double contact equal pin holder - The BA15S connector illuminates the Tail light (first brightness RED on both sections of LEDs) plus the Number Plate light (WHITE). Either terminal on the BA15D connector illuminates the Stop light (second brightness RED on both sections of LED) Please check the bulb holders in your ST51 D Lamp and see whether it has two single contact bulb holders or one single and one double (BA15D) holder - then select either the BA15S/BA15S or BA15S/BA15D panel These boards have a very low power requirement and provide great all over lens lighting from 51 RED LEDS, with the fast response time/illumination under braking characteristic of LEDs - plus good distinction between STOP and TAIL red light brightnesses. This is a 'plug and play' product that requires no other attachment other than plugging in the bulb connectors and locating the LED board between the lens and the lens retaining spring clip and reassembly of the lamp. Two 1.5mm thick rubber lens seals are provided in the kit, in case they are needed. Conversion kit for a PAIR of lamps. --
PAIR of LED light boards for conversion of Lucas ST51 'D Lamp' type lights, fitted with SPLIT RED lenses, to bright LED operation. On board electronics make this suitable for 6V & 12V vehicles and Positive & Negative earth systems. This is a new product specially designed to fit the Lucas ST51 split lens lamp and modern reproductions to the original pattern such as Vintage Supllies'/sVc's '249A and 428A' part number products. The panel features a main, D shaped RED light board with two sections of LEDs, that locates between the original lens and the lens retaining wire. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination, though the assembly is suitable for D lamps with or without a number plate illumination window. Two versions of this board are available to deal with different designs of 'D lamp': Two BA15S bulb holder connectors (15mm diameter, single contact cap with equal pins) on 15cm connecting wires. One connector illuminates the Tail light (first brightness RED on both section of LEDs) plus the Number Plate light (WHITE). The second connector illuminates the Stop light (second brightness RED on both sections of LED) One BA15S single contact holder and one BA15D double contact equal pin holder - The BA15S connector illuminates the Tail light (first brightness RED on both sections of LEDs) plus the Number Plate light (WHITE). Either terminal on the BA15D connector illuminates the Stop light (second brightness RED on both sections of LED) Please check the bulb holders in your ST51 D Lamp and see whether it has two single contact bulb holders or one single and one double (BA15D) holder - then select either the BA15S/BA15S or BA15S/BA15D panel These boards have a very low power requirement and provide great all over lens lighting from 51 RED LEDS, with the fast response time/illumination under braking characteristic of LEDs - plus good distinction between STOP and TAIL red light brightnesses. This is a 'plug and play' product that requires no other attachment other than plugging in the bulb connectors and locating the LED board between the lens and the lens retaining spring clip and reassembly of the lamp. Two 1.5mm thick rubber lens seals are provided in the kit, in case they are needed. Conversion kit for a PAIR of lamps. --
Kit of three WEDGE T10 base bulbs for Lucas type ST38 'Pork Pie' lamps that have been converted to STOP,TAIL & INDICATOR with the ST38CONV kit (or purchased as CA1249 lamps, with the same 3 x WEDGE T10 bulb holder) Two very bright B921LEDW-A bulbs (Indicator / Brake Light) and one Osram B117LEDWW-A (Side Light). Both these high quality bulbs accept 6 and 12 input voltages, so this one kit is suitable for 6 or 12V vehicles. A simple conversion of these popular lamps to LED operation, as an alternative to LED light panel CA1249LP-RAW - with both options providing good 6V solutions in the absence of a 6V equivalent to 12V incandescent bulb B921 (T10/T15 base 21W bulb). Kit converts one lamp, please buy 2 kits to convert a pair of rear lamps.
6V Positive Earth. 12 Amber LED, 7 Red LED tail light with 4 white LED number plate light. For lamp part number 211RA-S. two single contact equal pin BA15 bulb base connectors. High quality polycarbonate lens. Epoxy coated, fully sealed electronics. Recommend to upgrade flasher unit to item LEDFLASH2
12V Negative Earth. LED stop & tail conversion for 211/'Duolamp' type lamps. When brakes are applied, the "STOP" script illuminates in amber with a brighter, safer light than from standard incandescent bulbs. New technology for classic and vintage cars, motorcycles, and other custom applications that maintains an original appearance. Two single contact equal pin BA15 bulb base connectors. High quality polycarbonate lens. Epoxy coated, fully sealed electronics. Add plug in module part number 211RALED-PLATE for number plate light functionality. This is the LED cluster only - not a complete lamp. An alternative upgrade with 'STOP' script for 211RR, or 211RR-S if 211RALED-PLATE is added.
12V Negative Earth. All Red LED stop & tail conversion for 211/'Duolamp' type lamps. When brakes are applied, the stop LED cluster illuminates with a brighter, safer light than from standard incandescent bulbs. New technology for classic and vintage cars, motorcycles, and other custom applications that maintains an original appearance. Two single contact equal pin BA15 bulb base connectors. High quality polycarbonate lens. Epoxy coated, fully sealed electronics. Add plug in module part number 211RALED-PLATE for number plate light functionality. This is the LED cluster only - not a complete lamp. Upgrades part number 211RR or 211RR-S if 211RALED-PLATE is added.
6V Positive Earth. 12 Amber LED, 7 Red LED stop/tail light with 4 white LED number plate light. To upgrade lamp part number 211RA-S. One single contact equal pin BA15S (1156/SCC) bulb base connector (indicator function) and one offset pin BAY15D (1157) connector (stop, tail/number plate functions). High quality polycarbonate lens. Epoxy coated, fully sealed electronics. Recommend to upgrade flasher unit to item LEDFLASH3, 6V positive earth version, to eliminate the possibility of too rapid LED indicator flash. You will need to upgrade the bottom bulb holder socket on your lamp to a BAY15D socket with part number 211-CONV. This exclusive product provides STOP, TAIL, INDICATOR and NUMBER PLATE ILLUMINATION functionality all in one Duolamp cluster!
12V Negative Earth. 12 Amber LED, 7 Red LED stop/tail light with 4 white LED number plate light. For upgrade of lamp part number 211RA-S. One single contact equal pin BA15S (1156/SCC) bulb base connector (indicator function) and one offset pin BAY15D (1157) connector (stop, tail/number plate light functions). High quality polycarbonate lens. Epoxy coated, fully sealed electronics. Recommend to upgrade flasher unit to item LEDFLASH3, 12V negative earth version, to eliminate the possibility of too rapid LED indicator flash. You will need to upgrade the bottom bulb holder socket on your lamp to a BAY15D socket with part number 211-CONV. This exclusive product provides STOP, TAIL, INDICATOR and NUMBER PLATE ILLUMINATION functionality all in one Duolamp cluster!
12V Negative Earth. 12 Amber LED, 7 Red LED tail light with 4 white LED number plate light. For upgrade of lamp part number 211RA-S. Two single contact equal pin BA15 bulb base connectors. High quality polycarbonate lens. Epoxy coated, fully sealed electronics. Recommend to upgrade flasher unit to item LEDFLASH3, 12v negative earth version.
6V Positive Earth. 12 Amber LED, 7 Red LED tail light. For upgrade of lamp part number 211RA. Two single contact equal pin BA15 bulb base connectors. High quality polycarbonate lens. Epoxy coated, fully sealed electronics. Recommend to upgrade flasher unit to item LEDFLASH3, 6V positive earth version. Add plug in number plate light module 211RALED-PLATE to upgrade 211RA-S
12V Negative Earth. 12 Amber LED, 7 Red LED tail light. For upgrade of lamp part number 211RA. Two single contact equal pin BA15 bulb base connectors. High quality polycarbonate lens. Epoxy coated, fully sealed electronics. Recommend to upgrade flasher unit to item LEDFLASH3, 12v negative earth version. Add plug in number plate module 211RALED-PLATE to upgrade 211RA-S.
White LED number plate lens/LED light cluster module that plugs in to 211/'Duolamp' LED light clusters - 211RALED-STOP, 211RALED-RED, 211RALED and 211RA6LED, all pre-fitted with a wired tail/male connection that sockets with the female connection on this part.